For the past few years, I've been using my Gitzo Series 1 Mountaineer as my primary tripod. It served me well when my primary camera body was the Fujifilm X-T2, X-T3 and X-H1. Once I bought the GFX 50S to use alongside my X-H1, I became acutely aware of the tripod's shortcomings. The Gitzo Mountaineer Series 1 GT1542 is an excellent tripod. Combined with the lightweight Arca-Swiss p0 head, the tripod weighed in at just under 3 lbs and featured a very slim profile when folded down. The 25mm max leg diameter contributed to this slim profile, and while it works well with entry-level DSLRs and mirrorless camera bodies, the slim legs are just a bit too thin for a heavier, professional level body like the GFX 50S. Most people with a larger, heavier camera would be perfectly served with any Gitzo Series 1 tripod, as they only need it for single shots in adequate lighting. In my case, I use it primarily for landscape photography, astrophotography, night photography, etc... situations that require long exposures and/or multiple exposures for stacking, exposure blending or panoramas. This requires greater demands on my tripod as any movement between shots can ruin an exposure. It becomes difficult, if not impossible, to work with multiple, misaligned exposures in post-processing, thus a lighter-weight tripod can cause problems as any flexing will result in misalignment. While I haven't gotten rid of my Series 1 Gitzo, I recently bought a Gitzo GT3542 Series 3 Mountaineer.
I just read another article, this time from DPReview, comparing tripods and the author mentions paying attention to the load capacity so you can safely hang your bag from the hook for more stability. CUT IT OUT!!! STOP HANGING YOUR BAGS FROM YOUR TRIPOD!!! Read on for a better, safer way to stabilize your tripod.
A quick comparison between two products designed mostly to perform the same function. In case you're not familiar with an L-bracket, it's function is purely to allow rotation of your camera by 90 degrees while keeping it balanced on the X axis of your tripod. This is especially important for panoramas so the camera yaws directly over the center point rather than circumnavigating it, which alters the perspective enough to make stitching the result more difficult or even impossible.
Since buying this head, I've quickly learned to love it, especially after buying the necessary hardware that allows me to invert it as needed. The smooth design, reliability and light weight has helped it find a permanent home atop my Gitzo GT1542 Mountaineer tripod, supplanting the GH1382QD ball head that came with it.
As soon as I realized how the upright on the Ellie interfered with my battery door, I was able to devise a cheap solution for manufacture: a small bracket that would accept the rails and to attach the upright with truncated rails, aka screws, forward of the current position. I proposed the question to @3leggedthing's Twitter account, only to get, "we can't design a specific bracket for every camera and configuration I'm afraid."
Here's one of the first things I do when I buy a new camera: Secure the screws that secure the tripod screw port on the bottom of your camera.
You're familiar with how they all begin: "this video is sponsored by Squarespace." Ok, well, after that, they then feed you the next line, almost all of it verbatim, "I am not sponsored by (insert brand here). They have not paid me to do this review or told me what to say about it. This review is entirely my own and they don't know I'm making this video. I was/was not provided a sample for the purposes of this review. I am not biased in any way so you can trust what I'm about to say about this product." What they don't mention, obviously, is if they had to return that "review unit." But if you pay close attention, you may catch them using the product in later videos, especially if they were especially laudatory in their review. At least they weren't paid, right? Wrong. Payment is simply one form of compensation. That "review unit" usually comes along with an email that says, "you don't need to send this back to us." Simply put, the item itself is payment. Just because you didn't get to choose the item, the form of compensation or were given a special title associating you with their brand doesn't mean you weren't paid. They paid you with product and exclaiming otherwise is a flat out lie by Youtubers who persistently try to claim otherwise. Rarely are these items cameras and lenses; they're usually "soft goods" or accessories, like bags, lens filter kits, etc. that would likely get damaged during a thorough review period or whose cost of manufacture and/or retail price is so low that the cost of return, reconditioning and resale would consume all or more of the potential profit.
If you didn't already know, the Gitzo Mountaineer Series 0 and 1 Tripods come with fixed rubber feet. I can't speak for the 3 section versions, but generally the Mountaineer Series 2 and up come with 3/8"-16 threaded interchangeable feet, while those below have permanently affixed rubber feet. So I decided to buy a final leg section and foot for the GT1545T Traveler, already knowing it shared the 14.7mm leg diameter with my GT1542 Mountaineer but comes with a threaded cap to support 1/4”-20 interchangeable feet. The part number for the leg section is D106023 and the foot is D108623.
First, and most importantly, know what genres of photography you enjoy the most and if that genre requires a tripod. Then, buy the largest, highest quality tripod you're willing to carry that fits in your budget. Specifically in that order; do not put budget ahead of any other aspect of the tripod. If you go too cheap, you may very well end up with a tripod that meets none of your needs when you're forced to replace it due to instability or fragility. The adage, "buy cheap, buy twice (or more)" applies here.
As much as I like Gitzo as a brand and the quality of their products, some of their stuff just isn't as good as others. Take for example their leveling base; Gitzo features a large lever for tightening a head to the base and a handle borrowed directly from their sister Manfrotto's lineup. Instead, I got the series 3 leveling base from Really Right Stuff. It's lighter, has a simpler attachment system with no silly lever and a much sleeker locking handle with, get this, a gear hook! That hook alone is almost priceless, allowing me to attach weight for stability when I'm not leveling the head, ending any need to swap back to the flat top base. Back into the box that can go.
I finally have my dream 3 tripod setup. Gitzo Systematic GT3543LS+GH3382QD, Mountaineer GT1542+GH1382QD, and Traveler GT1555T+GH1382TQD. Next up is the Gitzo GM2542 Monopod and Mini Traveler Tripod. I plan to give all of them a thorough shakedown in Long Beach, WA in a couple of weeks and then in the North Cascades the week after. That is all.
BMW doesn't make a perfect car. While certain aspects may exceed those of other makers, those others oftentimes exceed that of BMW. Despite that, the Bavarian badge commands respect and with it comes an unmistakable allure for most when they see it. It's a symbol of quality but not necessarily the best and certainly not with all products that display the marque. The Bavarian roundel holds cachet for many and that's something very hard to quantify, an intangible factor that appeals to one's emotion rather than objectivity.
So, just like what happened with the deal on the Gitzo Mountaineer GT1542 + GH1382QD kit, I got a price alert on a Gitzo Traveler GT1555 + GH1382TQD kit for 45% off the advertised price of $989. So I bought it, because I have no self control.
Some first impressions after picking up an Arca-Swiss P0 Ball Head recently. Why? It's interesting. It's an inverted design so that the panoramic base is above the ball, ensuring a level platform for panoramic photography. Basically it eliminates the need for a leveling base. Combined with the 9oz weight, it'll reduce as much as 1.5lbs from my systematic tripod setup. I quickly discovered the reason for the weight savings: the base of the ball head is made of polycarbonate, most likely Delrin. The rest is made from either magnesium or aluminum, depending on the part. Regarding the design, it also has no protruding parts beyond the pano lock lever. The ball lock is performed by a rotating collar around the middle of the body, resulting in a sleek design. The ball is also aspherical, a feature used across Arca-Swiss' whole line, that increases friction to prevent your camera from loosely flopping over when the ball lock is loosened. A very elegant solution to a universal issue with all ball heads.
I'd prefer local buyers so I don't have to ship any of it. More importantly, I offer more than a few options for payment, be it Square, Square Cash, PayPal, Circle Pay, Zelle, or Chase Quick Pay. I'm able to accommodate all of these options because I'm legit. For gear, I have a couple of camera bags, 2 or 3 Benro tripods, a Slik tripod, Benro monopods, a few ball heads in various sizes, some tripod bags, a Formatt-Hitech Firecrest 100mm Filter Holder System with extra polarizer, adapters and original packaging, a Formatt-Hitech Standard 100mm Filter Holder, and random 100mm ND filters. There's probably even more in my storage closet I've forgotten about. If you're interested, leave a comment or email me directly.